Heavy Duty High Head Slurry Pump – SHH
The SHH combines a horizontal cantilever arrangement, double casing and replaceable wet-end components for abrasive slurry duties requiring higher head. Its published sizes, material options, adjustable impeller clearance and cartridge bearing assembly provide the basis for a duty-specific purchase, with wear parts and maintenance access considered alongside hydraulic performance.
Key word:
Slurry Pumps,Gravel Sand Pumps
Category:
High Head Slurry Pump
Need help selecting model? Contact our engineer.
Products detail
detail
What Specifications Are Published for SHH?
The catalog includes the five entries below. The performance basis is clear water; the proposed selection must account for the actual slurry. Use these ranges to organize candidates, then assess the required flow and head together on a configuration-specific curve.
Hydraulic Reference Values
| Published model | Capacity, m³/h | Capacity, L/s | Head, m | Head, ft | Speed, rpm | Listed maximum efficiency, % |
|---|---|---|---|---|---|---|
| M-1-SHH-C | 16.2–34.2 | 4.5–9.5 | 25–92 | 82.0–301.8 | 1400–2200 | 20 |
| M-2-SHH-D | 68.4–136.8 | 19.0–38.0 | 25–87 | 82.0–285.4 | 850–1400 | 47 |
| M-3-SHH-E | 126–252 | 35.0–70.0 | 12–97 | 39.4–318.2 | 600–1400 | 50 |
| M-4-SHH-S | 324–720 | 90.0–200.0 | 30–118 | 98.4–387.1 | 600–1000 | 64 |
| 6S-H | 468–1008 | 130.0–280.0 | 20–94 | 65.6–308.4 | 500–1000 | 65 |
Do not pair maximum capacity with maximum head as one operating condition. The speed range also does not mean that every listed flow-and-head combination can be achieved at every speed. Maximum efficiency is a catalog reference, rather than the efficiency expected throughout the duty range.
Power, Impeller and Suction Data
| Published model | Allowable maximum power, kW | Equivalent mechanical hp | Liner / impeller codes | Published NPSH, m | Impeller vanes | Impeller diameter, mm |
|---|---|---|---|---|---|---|
| M-1-SHH-C | 30 | 40.2 | M / M | 2–2.5 | 5 | 330 |
| M-2-SHH-D | 60 | 80.5 | M / M | 3–7.5 | 5 | 457 |
| M-3-SHH-E | 120 | 160.9 | M / M | 2–5 | 5 | 508 |
| M-4-SHH-S | 560 | 751.0 | M / M | 3–8 | 5 | 711 |
| 6S-H | 560 | 751.0 | M / M | 4–12 | 5 | 711 |
Allowable maximum power retains the catalog's meaning: it is a limit, not absorbed shaft power at the chosen duty or an automatic motor selection. The hp values convert that limit. The L/s and ft columns are rounded unit conversions.
NPSH means net positive suction head. An installation provides available NPSH; a pump has a required NPSH under specified conditions. Compare them with an appropriate margin. The published entries do not establish that margin or identify all corresponding duty conditions. Model codes, including 6S-H, remain as published; M / M identifies catalog codes rather than a complete alloy or compound specification.
Which SHH Features Matter in Abrasive Service?
Double Casing with Replaceable Hydraulic Components
The outer casing and replaceable wet-end components perform different roles. The casing provides the pressure-containing structure, while the impeller and liners form the hydraulic path exposed to slurry. The published replaceable components include the impeller, volute liner, frame plate liner and throat bush.
A renewal program can therefore identify the worn hydraulic components and retain other serviceable parts. Replacement decisions still depend on inspection, matching geometry and assembly condition. The design does not establish that the outer casing can remain indefinitely or that every damaged part can be reused.
Impeller, Liners and Clearance Adjustment
The impeller adds energy to the mixture; the volute liner collects flow leaving it, and the inlet-side components help define the flow path and clearances. The catalog lists five vanes for these entries. Passage capability needs the selected geometry and solids assessment, rather than vane count alone.
Adjustable impeller clearance is part of the published SHH arrangement. Set and inspect it using the delivered instructions. An adjustment is not a substitute for renewing components that no longer meet the applicable condition criteria.
Shaft, Bearings, Sealing and Drive
SHH descriptions identify a heavy-duty shaft and cartridge bearing assembly. For an abrasive installation, include alignment, lubrication access and component-handling space in the equipment review. These considerations connect the assembly to the maintenance tasks the site will perform.
Family options include packing, expeller and mechanical seals, with direct-coupled and belt-driven arrangements. Specify the proposed seal, utilities, leakage conditions and transmission. Their inclusion and suitability belong to the particular offer, so the selected configuration should be recorded with the pump's equipment identification.

How Should Wet-End Materials Be Compared?
Use the damage mechanism and liquid exposure to compare materials. Abrasion, cutting, impact and corrosion can occur together. Describe the solids distribution and chemistry, then identify the actual material for each component instead of ordering a general “wear-resistant” package.
| Material family | Useful starting questions | Limits to investigate | Purchase detail to record |
|---|---|---|---|
| High-chrome alloy | What abrasive minerals, impact and corrosion are present? | Alloy suitability, component loading and chemical exposure | Grade, component reference and agreed material requirements |
| Rubber or elastomer | Does the compound suit the liquid and particle shape? | Cutting by sharp solids, temperature, reagents and assembly geometry | Compound and approved operating conditions for the relevant parts |
| Polyurethane | Is a documented component available for this SHH assembly? | Availability in a wider parts range does not prove configuration suitability | Reviewed part identity, compound and compatible assembly |
Longteng's SHH information describes high-chrome alloy and rubber choices. Polyurethane needs separate component-level confirmation before it becomes part of an SHH order. None of these families defines one universal hardness, temperature limit or chemical range.
For a replacement, provide the installed material and photographs of the damage. Note whether loss is broad, concentrated at an edge, associated with cracking or accompanied by chemical attack. These observations help frame the review without proving a cause by appearance alone.
A material change can also require a change in compatible components or clearances. Keep the hydraulic selection tied to that assembly. The wet-end material selection guide gives a broader comparison, while the particle-size guide for wear parts explains what to report about normal solids and occasional oversize.
Where Is This SHH Configuration Worth Evaluating?
Abrasive Mineral-Processing Transfer
Consider SHH when abrasive mineral transfer also requires higher head at the process flow. Include the solids distribution, hardness where known, shape and feed variability. Distinguish ordinary operation from coarse-fragment or concentration upsets. A high-head designation by itself does not qualify the pump for every mill-discharge duty.
The mining pump application page places high-head equipment alongside other arrangements used at different plant positions. Select according to the position being served, then specify the relevant wear components.
Tailings Pipelines
For suitable tailings transfer, connect material selection with the pipeline duty and concentration range. Fine solids can remain abrasive, and a denser mixture may need a different performance assessment. Where the mixture's flow behavior requires rheological data, include it before selecting the pump and drive.
The tailings slurry pump application page supports the broader system review. Neither pipeline length nor a high solids percentage alone establishes the required SHH size, material or pressure rating.
Coal Preparation and Industrial Circulation
Coal slurry and industrial transfer can combine changing solids with variable process-water chemistry. Describe normal feed and credible upset conditions separately. Evaluate particle passage, compound compatibility, head and maintenance access for the proposed assembly. Use coal washing pump applications to identify the process duty before comparing equipment.
For industrial circulation, state all relevant liquid constituents and temperatures. An abrasion-resistant component should not be assumed chemically compatible merely because it performs acceptably on another slurry.
Which Published Sizes Should Enter the Shortlist?
The four SHH-coded rows below support a size-level comparison. They are not a ranking of wear life. Select among them using the duty curve, slurry assessment and proposed assembly; a larger impeller or higher catalog power ceiling does not automatically mean a better abrasive-service purchase.
| SHH-coded model | Published capacity, m³/h | Listed impeller diameter, mm | Comparison for the proposed duty |
|---|---|---|---|
| M-1-SHH-C | 16.2–34.2 | 330 | Review the lower-flow requirement and operating-point efficiency |
| M-2-SHH-D | 68.4–136.8 | 457 | Compare selected speed, duty range and actual material schedule |
| M-3-SHH-E | 126–252 | 508 | Check the curve, suction conditions and driver loading together |
| M-4-SHH-S | 324–720 | 711 | Review higher-flow duty with interfaces, component handling and power |
When comparing quotations, use the same required operating conditions. List differences in impeller, speed, material, seal and equipment scope explicitly. This is more useful than comparing the general descriptions “high head” and “heavy duty.”
Five Checks Before Ordering for High-Head Abrasive Duty
1. Record Real Operating Cases
State mixture flow, required head and hours spent at normal and credible extreme conditions. Identify which flow, concentration and density values occur together. A list of unrelated maxima can describe a duty the installation never experiences. Mark estimates so they can be resolved before approval.
2. Characterize the Wear Exposure
Provide particle-size distribution, maximum credible solids, shape, mineral type and known contaminants. Add concentration with its mass or volume basis, liquid chemistry and temperature. For existing equipment, include operating hours and where each component loses material. Avoid turning one previous replacement interval into a universal requirement.
3. Review the Curve and Pressure Conditions
Use a curve identified by model, impeller diameter and speed, showing head, efficiency and absorbed power against flow, with the applicable suction requirement. Assess the intended operating range. Separately establish allowable casing, flange and seal pressures, including inlet pressure and relevant transient conditions. Developed head and allowable pressure are different checks.
4. Match the Installation and Maintenance Tasks
Use the arrangement drawing to verify connections, flange details, shaft position, base dimensions and orientation. Check access for adjustment, lifting and wet-end removal. If existing piping, motor or base must remain, provide measured interfaces and nameplate information rather than assuming fit from nominal size.
5. Agree the Component and Supply Schedule
Identify each wetted component, material, seal, drive and included accessory. Separate commissioning spares from operating spares, with quantities and required documents. Agree the inspection and reporting scope. The metal pump parts range can help identify component families before the exact part references are settled.
What Should Maintenance Record When Wear Changes?
Keep component identity, operating hours and duty records together. Before inspection, follow the delivered instructions and the site's isolation procedures. Record changes in slurry, speed, flow, suction conditions and load so the physical findings have a useful operating context.
| Observation | Evidence to retain | Review direction |
|---|---|---|
| Broad impeller or liner erosion | Material identity, operating hours, solids and speed history | Compare present conditions with the selected duty and material |
| Localized throat bush or liner loss | Location photographs, clearance records and matching-part condition | Review assembly condition and hydraulic operation before repeating the order |
| Noise, vibration or hotter bearings | Trend, load, speed, feed level and timing of the change | Review suction, alignment, lubrication and rotating condition |
| Reduced flow or head | Measurements, wear condition and any pipeline or drive changes | Check the complete system and pump before proposing a larger driver |
Define replacement criteria from the applicable equipment instructions and condition assessment. Do not continue adjustment beyond permitted limits or infer remaining pressure integrity from outside appearance. For repeated failures, the heavy-duty pump wear investigation guide provides a detailed review sequence.

Frequently Asked Questions
Is This a Separate, Higher-Rated SHH Variant?
The published information identifies the same SHH family and catalog entries used elsewhere in the range. “Heavy duty” does not by itself establish a higher pressure class, thicker casing or different metallurgy. Compare actual assembly descriptions and documented limits when evaluating offers. The ordered model, impeller, material, seal and permissible conditions identify the equipment more reliably than an application label.
Is Allowable Casing Pressure the Same as Pump Head?
No. Head describes the energy added per unit weight of the pumped mixture; a casing pressure rating describes a limit for the pressure boundary under stated conditions. Inlet pressure and mixture density matter when evaluating actual pressure. Review the casing, flanges and seals for the proposed installation, including applicable transient conditions. A catalog head range cannot be used as a complete pressure-rating statement.
Will a Harder Alloy Always Extend Wear Life?
No. Hardness alone does not establish resistance to the combination of abrasion, impact and corrosion in an actual component. Compare the identified grades, component geometry and expected exposure. If the previous part cracked or suffered localized damage, retain it for examination rather than assuming a harder material will solve the problem. Agree the material and inspection requirements for the replacement instead of purchasing on hardness alone.
Should We Replace Only the Impeller or the Complete Wet End?
Base the scope on inspection of the complete assembly. A worn impeller may have matching liners or inlet-side components that also need attention, but that does not mean every overhaul requires all new parts. Record component condition, clearances and material identity against the equipment references. The order should identify which components will be renewed and which serviceable parts will remain in the reviewed assembly.
What Is a Useful Basis for Comparing Proposed Wear Life?
Use operating hours and a defined duty, with component identity, material, solids, speed and replacement criteria recorded. Calendar months without that context can be misleading. Site history can support a comparison, but changes in feed or operation may prevent a direct match. Any contractual wear-life condition needs an agreed measurement method, operating assumptions and exclusions; a general product description does not establish that commitment.
Can a Larger Motor Restore Head Lost Through Wear?
A larger motor alone does not repair worn hydraulic components or change pump performance at the same speed and geometry. First verify the duty, measured speed, condition, clearances and system changes. A proposed speed or impeller change requires a new hydraulic, mechanical and power review, including equipment limits. Replacing the driver without that review can leave the original problem unresolved and create additional loading concerns.
What Should an Overhaul Spare-Parts Quotation Identify?
It should tie each item to the pump and reviewed component schedule. Provide the model, available assembly or serial identification, part references, drawings or dimensions, material and quantity. Describe a replacement as “dimensionally interchangeable with” an existing part only after its relevant interfaces are verified. Record any approved substitutions, required inspection documents and item-specific delivery terms so maintenance receives the components it intended to order.
Request an SHH Heavy Duty High Head Pump Quotation
Send Longteng the required flow and head, normal operating range, slurry density, concentration basis, particle description, chemistry and temperature. Include suction conditions, piping information and the intended installation. For a replacement or wear problem, add the existing model, component references, material records, operating hours and clear photographs of the damaged areas.
State whether the request covers a bare pump, driven assembly, wet-end renewal or operating spares. Add quantity, destination and documentation requirements. Contact Longteng Pump with the information available so the proposed SHH assembly, supply scope and commercial conditions can be defined in the offer.
Sources and What They Support
- Improving Pumping System Performance: A Sourcebook for Industry — Supports the general discussion of operating-point selection, pump and system performance, and maintenance as part of equipment life-cycle evaluation.
- Hydraulic Institute Pump FAQs — Supports the discussion of operating regions, suction conditions, bearings, seals and maintenance records. These sources do not establish SHH model ratings, wear life or Longteng commercial commitments.
Prev
None
Next
ONLINE MESSAGE
Related products